EMC QLogic Instalační příručka Strana 112
- Strana / 150
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
110
EMC Fibre Channel and iSCSI with QLogic Host Bus Adapters in the Windows Environment
Miscellaneous Planning and Procedures
Setting up external boot for IBM BladeCenter server HS40 (8839)
This section contains the folloiwng information:
◆ “Configuring an HS40 BladeCenter server to boot from an
external array” on page 110
◆ “Blade server restrictions” on page 111
Configuring an HS40 BladeCenter server to boot from an external array
IBM HS40 (8839) BladeCenter servers encounter a dual-port HBA
conflict when attempting to configure boot BIOS to boot from an
external array. To configure an HS40 BladeCenter server to boot
successfully follow the steps below.
1. Create a single zone containing the HBA port from which you
want to boot. This prevents any conflicts with the other fibre port.
2. Configure the QLogic BIOS to boot from the EMC array as
described earlier in “QLogic Fibre Channel HBA BIOS/boot LUN
settings” on page 26. During server POST, be sure that the QLogic
banner displays the selected boot LUN correctly before
continuing.
3. Reboot the host and press
F1 to enter the server BIOS
Configuration/Setup Utility.
4. Select Devices and I/O Ports and press Enter.
5. Select IDE Configuration Menu and press Enter
6. Select the Onboard PCI IDE Controller and press Enter. Under
the options menu, set this IDE Controller to disabled. This will
disable the internal IDE disk drives.
7. Press
ESC twice to return to the IDE Configuration Menu and
then select Start Options and press Enter.
8. Select Startup Sequence Options and press Enter.
9. Select Third Startup Device and press Enter.
10. Select HAx PortID xxxxxx xxxxx and press
Enter. This boot device
will be replaced as the Third Startup Device in the Startup
Sequence Options.
11. Press ESC until you are prompted to save your changes. Then exit
the BIOS Configuration/Setup Utility.
- Windows Environment 1
- Contents 3
- Chapter 3 Troubleshooting 5
- Courier italic 15
- Installation and 17
- Configuration 17
- How this guide works 18
- Verify Array/LUN 19
- Visibility for Boot 19
- Installing the HBA 20
- STOP: 0X0000007B 21
- HBA edge connecters 23
- PCI Express slots 24
- PCI Express slots aligned 24
- QLogic banner 29
- Main Fast!UTIL options window 30
- Configuration Settings window 30
- Adapter Settings window 31
- Enter 34
- Warning dialog 35
- Fast!UTIL Options window 36
- Firmware boot manager menu 38
- refer to memory ramdisks 39
- QLogic directory 41
- EFIutil.efi 41
- QLogic efiutil all upgrade 43
- QLogic Fibre Channel drivers 45
- Driver handle numbers 46
- -s 5f 62 46
- Edit adapter settings 47
- Connection option 48
- Figure 32 Options set 50
- RAMDISK 51
- Windows 52
- HBA selection screen 57
- Windows setup screen 58
- Base article Q240672.) 59
- Existing partitions 59
- Windows Boot Manager 62
- Windows Setup screen 62
- Windows Install screen 63
- Loading driver screen 66
- Browse for Folder screen 67
- A as shown in Figure 47 67
- Install Windows screen 70
- Pre-installation guidelines 71
- Driver installation/upgrade 72
- SANsurfer driver selection 74
- Post-installation procedures 78
- SANsurfer HBA install wizard 79
- Show SAN 82
- SANsurfer icon 83
- Connect to the host 84
- ServerManager: 85
- <sp_IP> 88
- <storagegroupname> 88
- Miscellaneous 91
- Planning and 91
- Procedures 91
- Download Firmware dialog box 97
- F1 to enter the server BIOS 112
- Enter. This boot device 112
- Blade server restrictions 113
- Driver revision 114
- Where to find the driver 115
- Windows 2003 STORPort updates 116
- STORPort drivers 117
- A:\, for 120
- QLogic advanced utilities 123
- Utilities tabbed page 125
- EMC CLARiiON storage arrays 127
- Set the HBA FC-AL loop ID 130
- Reconfigure the HBA jumper 133
- Troubleshooting 135
- Volume sizes 136
- Host after the rebooted 141
- Known issues 142
- Problems and solutions 143
- Problem 4 144
- Problem 5 144
- Problem 6 144
- Problem 7 145
- Problem 8 145
- Problem 9 145
- Third-Party Software 147
- SANsurfer version history 148
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce